Network Appliance NS0-592 Exam Dumps - PDF Questions and Testing Engine
Latest NS0-592 Exam Dumps for Pass Guaranteed
NEW QUESTION 21
Click the exhibit button.
Your customer has severe latency on one of their SATA aggregates. You run the statit -b and statit -e commands to obtain detailed disk statistics.
Referring to the output shown in the exhibit, which disk would be the problem?
- A. 0a.11.19
- B. 0a.11.21
- C. 0a.11.23
- D. 0a.13.21
Answer: A
NEW QUESTION 22
A customer reports that copying data over iSCSI attached LUNs is taking significantly longer than usual. The customer asks you to help to identify the root cause of this problem.
Which two perfstat sections would you use to accomplish this task? (Choose two.)
- A. stats lun
- B. stats volume
- C. statit
- D. lun stats -vserver
Answer: C,D
NEW QUESTION 23
Your customer states that the storage efficiency on their FAS 8200 is far below what they had expected for a VMware NFS datastore. They enabled deduplication three days ago. The job ran every night for only 10-20 minutes, and the space savings now is less than 5%.
What is causing the space savings to be so low?
- A. They have enabled aggregate-level inline data compaction, so the savings are at the aggregate level.
- B. They have not enabled volume-level compression.
- C. They have enabled aggregate-level inline deduplication, so the savings are at the aggregate level.
- D. They have not run a baseline deduplication to scan old data.
Answer: B
NEW QUESTION 24
Click the exhibit button.
A customer reports that storage latency has recently increased substantially. No changes have been introduced, and the traffic did not change.
Referring to the output shown in the exhibit, which corrective step should be taken?
- A. Move some volumes off the affected aggregate.
- B. Add more spindles.
- C. Throttle the client traffic.
- D. Perform the volume reallocation.
Answer: C
NEW QUESTION 25
A customer reports that a takeover has been disabled on an HA pair.
What would be a cause for this to happen?
- A. The cluster network is not functioning properly.
- B. The interface for the hardware assist has become unavailable.
- C. There is a disk running too hot.
- D. The HA interconnect is not functioning properly.
Answer: D
NEW QUESTION 26
In a 4-node cluster, nodes 1 and 2 are an HA pair, and nodes 3 and 4 are an HA pair. The following error appears in the log.
12/15/2018 15:48:47 node-2CRITICALclam.node.ooq: Node (name=node- 2, ID= 1001) is out of "CLAM quorum" (reason =quorum update).
In this scenario, which two statements are correct? (Choose two.)
- A. Node 2 takes over node 1.
- B. All LUNs are online in the cluster.
- C. Node 1 takes over node 2.
- D. All LUNs are offline in the cluster.
Answer: C,D
NEW QUESTION 27
For restore purposes, a storage administrator on an ONTAP system created a FlexClone of a volume that contains a LUN from a specific snapshot. This LUN cannot be seen by a Windows client after a disk rescan is performed by using Disk Management.
In this scenario, which statement is correct?
- A. The cloned LUN needs to be mapped to an initiator group.
- B. The cloned LUN must be brought online.
- C. The cloned LUN must be renamed to a different name than the name of the source LUN.
- D. The cloned volume must be split from the source volume before the LAN can be used.
Answer: D
NEW QUESTION 28
A customer's FAS8200 node1 went down an hour ago after a WAFL inconsistency error. All data is being served from partner node2, but the storage failover show command output is not showing a node1 as "Waiting for giveback".
What is the corrective action for this situation?
- A. Re-create the root aggregate on node1.
- B. Boot the system and run the wafliron command on the inconsistent data aggregate.
- C. Boot the system and run the WAFL_check command on the inconsistent data aggregate.
- D. From the LOADER prompt, run the wafliron command on the system's root aggregate.
Answer: A
NEW QUESTION 29
When you issue a volume clone create command, which entity in WAFL is copied?
- A. the vol_info block
- B. the buftree
- C. the inode file
- D. the data block
Answer: C
NEW QUESTION 30
Click the exhibit button.
You have just cabled a new shelf to a FAS8200. Running the system node run -node * sysconfig - a command indicates that multipath HA is configured. However, after running Config Advisor, you receive an error that your cabling is incorrect.
As indicated in the exhibit, which two actions will correct the cabling? (Choose two.)
- A. Move the 0b SAS connection on the top controller to 0d on the top controller.
- B. Move the 0b SAS connection on the bottom controller to 0d on the bottom controller.
- C. Move the 0b SAS connection on the top controller to 0d on the bottom controller.
- D. Move the 0b SAS connection on the bottom controller to 0d on the top controller.
Answer: A,B
NEW QUESTION 31
Click the exhibit button.
A customer notifies you that Active IQ is showing a warning that a broadcast domain in their environment has been configured with ports from multiple VLANs.
Referring to the exhibit, which two statements are correct? (Choose two.)
- A. You should move the e0M ports to a Broadcast Domain that is dedicated to only management traffic.
- B. A VLAN tag cannot be assigned to the e0M port, so the configuration is acceptable.
- C. You should change the LIF service policy to net-intercluster to prevent the LIFs from failing over to the e0M ports.
- D. You should configure e0M so that is tagged on VLAN 40.
Answer: C,D
NEW QUESTION 32
A non-maskable interrupt event occurs. The system panics and then reboots.
In this scenario, what would have caused the panic?
- A. a secd process
- B. a watchdog timer
- C. an ICMP blackhole detector
- D. a volume location distributed database
Answer: B
NEW QUESTION 33
Click the exhibit button.
Your customer added a new DS4246 shelf to their FAS system. They created an aggregate on the new shelf.
Two weeks later, they log in to Active IQ and discover the Medium Impact error shown below.
"Both SAS connections from one controller go to the same shelf."
Referring to the exhibit, which statement is correct?
- A. You are unable to obtain a "Cable Visualization" overview from Active IQ.
- B. A faulty cable is causing the problem.
- C. A faulty IOM is causing the problem.
- D. You can correct this problem without downtime on the FAS system.
Answer: D
NEW QUESTION 34
A customer reports that one their SVMs has two default gateways. The customer wants to know whether this behavior is expected or if one of gateways should be deleted.
In this scenario, what do you tell the customer?
- A. This situation is a misconfiguration, and the customer should delete one of the default gateways because there can be only gateway for each SVM.
- B. The configuration is acceptable only if both default gateways are in the same subnet.
- C. The configuration is acceptable if the customer configures different metrics on all defaults routes.
- D. The configuration is acceptable. The customer can achieve load balancing between the default gateways by setting the same metric on all default routes.
Answer: C
NEW QUESTION 35
Your customer added a new DS2246 shelf to an existing stack on their FAS8060A system. The customer then noticed that the new shelf's disks appear with the shelf serial number instead of the shelf ID in the sysconfig -r command output.
What is the reason for this problem?
- A. The ACP is cabled incorrectly.
- B. The new shelf has the same ID as another shelf.
- C. There is failed IOM module in the new shelf.
- D. The SAS is cabled incorrectly.
Answer: D
NEW QUESTION 36
A customer has a 2-node MetroCluster. They experienced a complete power loss at site B.
The customer has lost connectivity to site B and now realizes that the DR partner at site A has not taken over the DR partner at site B.
Which two actions must be performed in this scenario? (Choose two.)
- A. On the DR partner at site A, perform the process to heal the data aggregates.
- B. On the DR partner at site A, perform the process to switchover.
- C. On the DR partner at site B, perform the process to heal the root aggregate.
- D. Ensure that site B is prevented from serving data or simply powered off (nodes and disk shelves).
Answer: B,C
NEW QUESTION 37
Click the exhibit button.
A customer has the ns-switch shown in the exhibit.
Which two statements are true in this scenario? (Choose two.)
- A. User names not present in the local database are looked up in LDAP.
- B. Groups can be looked up both in the local database and in LDAP.
- C. User mapping decisions are always based on the LDAP configuration.
- D. Host names are always resolved using the configured DNS server.
Answer: B,D
NEW QUESTION 38
Click the exhibit button.
A storage administrator reports that when they enabled Vscan, they began receiving reports of CIFS users having very slow access to all their files. The storage administrator recovered from the issue by disabling Vscan on their SVM. The storage administrator was able to collect perfstat output during the time of the reported slow access, as shown in the exhibit.
In this situation, what is the problem?
- A. The problem is on the SVM, as shown in the scan_latency output.
- B. Vscan server 192.168.100.144 was slower than Vscan server 10.23.23.54 in completing Vscan requests.
- C. The problem was with both Vscan servers 192.168.100.144 and 10.23.23.54.
- D. Vscan server 10.23.23.54 was slower than Vscan server 192.168.100.144 in completing Vscan requests.
Answer: B
NEW QUESTION 39
You configured iSCSI multipathing on a Windows host to a 2-node ONTAP cluster so that you can attach to some LUNs. You see that the host logging in to both iSCSI LIFs in the ONTAP cluster, and you notice that the igroup is correctly set. After you open Disk Management and rescan for disks, the NetApp LUNs do not show up.
In this scenario, what should be performed to enable the LUNs to be visible to the Windows host?
- A. Set up Selective LUN Mapping (SLM) and try scanning again.
- B. Configure the ONTAP nodes for HA and try scanning again.
- C. Set up LUN mapping and try scanning again.
- D. Configure the SVM for FCP and try scanning again.
Answer: A
NEW QUESTION 40
What is a major difference between NFSv3 and NFSv4.x?
- A. NFSv4.x requires an auxiliary protocol for status monitoring, and NFSv3 does not.
- B. NFSv4.x is stateless, and NFSv3 is stateful.
- C. NFSv4.x is stateful, and NFSv3 is stateless.
- D. NFSv4.x requires an auxiliary protocol for mounting, and NFSv3 does not.
Answer: C
NEW QUESTION 41
A new cluster running ONTAP 9.5 has just been installed and you want to create a FlexGroup volume. Which action will accomplish this task?
- A. Use the storage pool create command.
- B. Use the volume size command.
- C. Use the volume create command.
- D. Use the Deploy utility to provision the FlexGroup volume.
Answer: A
NEW QUESTION 42
End users are complaining of high latency when accessing an ONTAP 9 luster.
Which command helps you to determine whether there is a storage component that is contributing to this problem?
- A. qos statistics latency show
- B. sysstat -c 30 -M 1
- C. wafltop show -v -cpu -I 10 -c 5-n 6
- D. qos statistics performance show
Answer: D
NEW QUESTION 43
Click the exhibit button.
A customer reports that their system recently began logging an error.
Referring to the exhibit, which two statements are correct? (Choose two.)
- A. The spmd application failed to restart the ntpd daemon.
- B. A user is attempting to restart the ntpd daemon.
- C. The bcomd application is responsible for monitoring the observed behavior.
- D. The ntpd daemon is responsible for time services.
Answer: B,D
NEW QUESTION 44
After you replaced the motherboard, the node stopped in the "waiting for the cluster application to come online" state.
Which two actions should you perform to troubleshoot this problem? (Choose two.)
- A. Verify that the physical links on the cluster ports are up.
- B. Check the status of the HA with the interconnect-up field of storage failover show command.
- C. Check the status of the cluster with the cluster ring show command.
- D. Verify the setting of the cluster interconnect switch.
Answer: B,C
NEW QUESTION 45
An administrator wants to keep an automatic daily up-to-date copy of a volume at a disaster recovery location.
What should the administrator do to achieve this goal?
- A. Configure a SnapMirror relationship to the remote location.
- B. Perform an NDMP dump to the remote location.
- C. Configure a SyncMirror relationship to the remote location.
- D. Perform a volume relocation to the remote location.
Answer: A
NEW QUESTION 46
......
Reliable Network Appliance NCSE NS0-592 Dumps PDF Nov 19, 2021 Recently Updated Questions: https://pass4sure.practicedump.com/NS0-592-exam-questions.html